How to Replace a Holster Clip With the Tacware 5 Hole Straight Clip
By Shop Tactical Gear & Holsters丨Guerrilla Tactical | Published: 2026-11-03
Category: Návody
Swap a worn or loose holster clip in five steps. Use the Tacware 5 Hole Straight Clip for secure belt retention, easy finger-grab removal, and adjustable hole spacing.
Quick answer
Remove the old clip, match the new clip’s hole pattern to your holster’s mounting holes, and reinstall using the original screws or a matched thread. The Tacware 5 Hole Straight Clip gives you five positions for precise adjustment and a built-in finger-grab for easier on-off.
Why swap the clip instead of the whole holster
A clip is a wear item. If your current clip has lost tension, cracked at a screw hole, or no longer hooks your belt consistently, replacing just the clip is faster and cheaper than replacing the holster. The Tacware 5 Hole Straight Clip is a straight, belt-hooking design with a finger-grab at the end, so you can remove the holster without prying at the clip body.
Check your holster’s hole pattern first
The 5-hole design offers adjustment, but it only helps if the hole spacing matches your holster’s existing mounting holes. Before ordering, compare the center-to-center distance and thread size of your current clip to the Tacware clip. If the spacing is different, you may need to drill new holes or use a mounting plate—neither is included with the clip. This is a decision limitation, not a defect: the clip is designed for holsters with a compatible hole pattern.
Reuse or match your screws
Holster clip screws are not universal. Keep the original screws if they are in good condition and still thread properly. If a screw is stripped or lost, match the thread pitch and length to your holster’s hardware—do not force a different screw, as it can crack the holster shell. The Tacware clip does not ship with screws, so confirm your hardware before you start.
Step-by-step clip replacement
- Unload and clear the holster: Remove the firearm and any magazine or accessory from the holster. Work on a bench with the holster empty. Common mistake: leaving a loaded gun in the holster while turning screws—always clear it first. Confirm the holster is empty before touching any hardware.
- Remove the old clip screws: Use a properly sized screwdriver or hex key. Turn counterclockwise while pressing firmly to avoid stripping the screw head. Keep the screws and any washers in a small tray. Checkpoint: if a screw will not budge, apply a small amount of penetrating oil and wait before trying again. Stop if the screw head starts to round—forcing it will make removal harder.
- Compare hole spacing and test-fit the new clip: Place the Tacware 5 Hole Straight Clip over the holster’s mounting holes. Align one hole that gives you the ride height you want. Do not tighten anything yet. Common mistake: assuming all five holes will line up with your holster—only the holes that match the existing pattern are usable without modification. If no hole aligns, do not drill until you confirm the clip is the right model for your holster.
- Start screws by hand, then snug them down: Thread each screw by hand first to avoid cross-threading. Once all screws are started, tighten them in a cross pattern until the clip is secure but not crushing the holster material. Checkpoint: the clip should not shift when you press on it, but you should not see the holster shell deform around the screw head. Recheck screw tension after the first range session; vibration can loosen them.
- Test retention and finger-grab clearance: With the holster empty, hook the clip over a belt or a representative strap. Pull gently to confirm the clip hooks securely. Then use the finger-grab to lift the clip off the belt. Common mistake: mounting the clip so close to the holster body that you cannot get a finger under the grab. Adjust to a different hole if clearance is tight. If the clip releases too easily or will not release cleanly, remount before carrying.
Product facts
- Tacware 5 Hole Straight Clip: The Tacware 5 Hole Straight Clip has a built-in finger-grab at the end of the clip. That makes installation and removal quicker because you can pull the clip away from the belt without digging at the edge.
Tacware 5 Hole Straight Clip - Tacware 5 Hole Straight Clip: The 5-hole design allows precise adjustment and compatibility with various belt sizes. You can fine-tune ride height and retention position rather than accepting a single fixed mounting point.
